2/8/2024 0 Comments Rec tec bullseye error codesLoose wire connections on the controller board may stop the grill from lighting. GFI is tripping, and the computer will not turn on are the indicators that let you know it’s the hot rod.Īlso, look at the firepot, and if it gets pellets but won’t light, we bet it’s the defective ignitor rod.Īpart from these, a clogged auger or defective auger motor is also responsible for not turning on the grill.Īnd lastly, the controller board issue is another reason that stops your grill from turning on. Thirdly, the Rec-Tec igniter not working is another grill issue that causes your grill to not light. Your Rec-Tec will not ignite if the temp dial remains in the Off position. Secondly, the temperature dial issue may also encourage your grill from lighting. A blown fuse is also responsible for this issue. A defective GFCI outlet or tripped outlet is the first culprit that prevents your grill from turning on.īesides, you will fail to light your grill if you don’t turn the power switch to the On position. Your Rec Tec Bullseye will not turn on for several reasons. And this chapter will educate you about those grill issues and provide the solutions as well. Just like other appliances, you will also go through some Rec-Tec problems over time. However, it doesn’t mean the grill will never get defective. It helps you to cook mouth-watering smoked meat or food. Rec-Tec is a widely accepted grill brand every grill lover trusts. Does the Rec Tec Bullseye have WiFi? 7 Common Rec Tec Bullseye Problems & Their Solutions.How long does it take Rectec bullseye to heat up?.What temp is low on the Rec Tec bullseye?.Pellets Not Being Delivered To The Fire-Pot Rec Tec Grill Won’t Heat Up Or Maintain Proper Temp 7 Common Rec Tec Bullseye Problems & Their Solutions.Finally, test the igniter rod to see whether it’s working or not.Use a zip tie to secure all the wires to prevent them from blocking the motor and fan. Then, attach the new igniter rod wire to the red wire bundle. Now, install the Molex connector to the new igniter wire. Push the hot rod wires through the grommet hole. Locate the four screws holding the blower fan in place and remove them.Tuck the igniter rod wire into the airbox and replace the fire pot in its place & screw down all four screws.Make sure you don’t over-tighten the nut. Put the new igniter rod in the fire pot and tighten the nut to hold the igniter rod into its place.Now, remove the old igniter rod from the fire pot by loosening the bolts with a 2.5 Metric Allen Wrench.Pull the fire pot toward you and spin counterclockwise to remove the fire pot.Then, unscrew the four screws on the fire pot. Set your grill upright and open the lid.Then, cut the end off of the old igniter wire. Disconnect the igniter or hot rod wire from the red wire bundle.Cut and pull out all zip ties you see and free your wires.Remove a total of 6 screws to pull out the cooking grate.Start by unplugging your Rec-Tec grill from the power.And this chapter will let you learn how to replace a hot rod on Rec-Tec. No matter which signs you notice, replacing the igniter rod is the only solution to let your grill function correctly. It means the pellets are not burning due to a defective hot rod. If you find the wood pellets are feeding but overflowing, understand the igniter or hot rod is not functioning. Rec-Tec Error Code 2 is a sign of a failed ignitor rod. Then, understand it’s the hot rod, and you need to replace it. The blower fan is functioning, but still, your Rec-Tec grill isn’t lighting.Now, inspect the fire pot visually, and if after 10 minutes: Now, pull out the cooking grate and remove the flame deflector. Grill Won’t Light But Pellets FeedingĮnsure you turn the igniter switch in the On position. All of these indications will let you know about a faulty hot rod or igniter rod. If the fuse gets blown out, it’s because you have got a hairline crack in the igniter rod. It blew a fuse that’s a 5 amp fuse which is located right behind the power button. The computer of the Rec-Tec Grill will not turn on. Tripping GFCI or Defective ComputerĪ tripped GFCI (which is 99% of the time out of a hundred) will indicate that the igniter rod gets defective. The following signs will let you know if the igniter rod is not functioning properly. If it stops working, your grill will not light or ignite. The igniter rod or hot rod is responsible for burning the wood pellets.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |